Mazda 0000-8F-N02B Owner's Manual

14280159 Rev. A 10/10PART NUMBER (s):0000-8F-N02BAPPLICABLE MODELS:2007 > MAZDA CX-9ALL MODELSREMOTE START SYSTEMKIT CONTENTS Remote Start

10 4280159 Rev. A 10/10IGNITION SWITCH CONNECTOR1. Route the remote start ignition harness with 6-pin male and fe-male ignition connectors over the fa

114280159 Rev. A 10/10KEY-IN-SENSE & PUSH WIRE ROUTING1. Route the remote start harness YELLOW/BLUE and BROWN/BLACK wires along with the im-mobili

12 4280159 Rev. A 10/10BR/BCIGAEBDFHJLKWIRE HARNESS CONNECTIONS - STEERING COLUMN, continuedKEY-IN-SENSE CONNECTION1. Locate the 12-pin (Smart-Key equ

134280159 Rev. A 10/10Ribbon Cable Non-conductor sideConductor sideIMMOBILIZER INTERFACE RIBBON CABLE MOUNTING91. Route the immobilizer i

14 4280159 Rev. A 10/10VEHICLE’S HORN WIRE REMOTE START HARNESS WIRE GREEN/RED GREEN/REDNOTE: Refer to Page 2 for IDC Wire Tap Procedure and

154280159 Rev. A 10/10DOOR LOCK CONNECTION1. Locate the 30-pin WHITE connector at the Body Control Modulemounted in the left kick panel area. (FIGURE

16 4280159 Rev. A 10/10TACHOMETER CONNECTION1. Locate the upper 66-pin BLACK (2007 - 2010 Models) or the middle 70-pin BLACK (2011 Models) connector

174280159 Rev. A 10/10RE-ASSEMBLY1. Re-install the following components:a. Plug the ignition key light back into the lower steeringcolumn cover (Retra

18 4280159 Rev. A 10/10RE-ASSEMBLY, continuedf. Re-install the driver’s side scuff plate by engaging all threeclips. (FIGURE ZZ)2. Re-install and Rec

194280159 Rev. A 10/1018TACHOMETER PROGRAMMING1. Tachometer Programming - Make sure engine hood is closed!a. Turn the ignition key to the RUN position

2 4280159 Rev. A 10/10ELECTRICAL SYSTEM GENERAL PROCEDURES0Connector diagrams Connector diagrams show connectors on the harness side. The terminal in

20 4280159 Rev. A 10/10IMMOBILIZER INTERFACE PROGRAMMINGNOTE: THE TACHOMETER SIGNAL MUST BE PROGRAMMED TO THE DNA CARD FOR THE REMOTE ENGINESTART FUN

214280159 Rev. A 10/10FUNCTION TEST2120Car Find1. Press and hold START button - Horn should beep six times and parking lights should flash six times.

22 4280159 Rev. A 10/1022TROUBLESHOOTING GUIDE1. Horn honks 4 times & vehicle does not remote start - No tachometer signal learned to DNA card.a.

234280159 Rev. A 10/10FINALIZING THE INSTALLATION1. NOTE: After reassembling the vehicle parts, check for any dirt. Clean any dirty parts.2. NOTE:

24 4280159 Rev. A 10/10SERVICE PART NUMBER LIST25Part Number Description0000-8F-H03 Hood Safety Switch Kit Service Part0000-8F-H05A Mazda Immobilizer

254280159 Rev. A 10/10SYSTEM LAYOUT

26 4280159 Rev. A 10/10• Inspect the installed / reinstalled parts for the following items: : Applicable *1: Horn beeps and parking lights flash s

34280159 Rev. A 10/10VEHICLE PREPARATION 1. Disconnect and Remove Battery a. Disconnect and isolate the negative and positive batteryterminals. (

4 4280159 Rev. A 10/10VEHICLE PREPARATION; continuedb. Remove the driver’s side kick panel by removing the plas-tic nut. (FIGURE C) Partially peel b

54280159 Rev. A 10/10REMOTE START CONTROL MODULE PREPARATION1. Insert the supplied fuses into the remote start control module as shown below. (FIGURE

6 4280159 Rev. A 10/101. Driver’s A-Pillar Trim Removal/Installationa. Partially peel back the rubber weatherstrip away from theA-pillar trim.b. Pull

74280159 Rev. A 10/10HOOD SAFETY SWITCH MOUNTING1. Using (2) supplied, 1/4” self drilling screws and (2) supplied lock washers, secure the hood safety

8 4280159 Rev. A 10/10 Hood SafetySwitch Wiring Main WireHarness GrommetHOOD SAFETY SWITCH MOUNTING, continued4. Using fish wire, pull the hood

94280159 Rev. A 10/10GROUND CONNECTION1. Locate the 10 mm factory bolt, mounted high up under the dash, near the vehicle dashwall,supporting the facto